Multi-line 2 BGC Application Software series 2.x.

Multi-line 2 BGC Application Software series 2.x.

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

2.50.3

This software applies to the following DEIF products:

Multi-line 2 - BGC

Multi-line 2 - BGC-L

Changes:

  • 1- Update of self-check functionality

2.50.3

13/04/2015

This software applies to the following DEIF products:

Multi-line 2 - BGC

Multi-line 2 - BGC-L

Changes:

  • 1- Update of self-check functionality

2.50.2

14/03/2013

Changes:

  • Start attempt settings was ignored.Corrected.
  • Minimum load in AMF was ignored.Corrected.

2.50.1

30/10/2012
  • The breaker did not open in Semi auto AMF mode. Only L1 decides if the frequency has dropped 0.5 Hz. Corrected.
  • The ramp down speed setting was ignored in Island mode and just ramped down as fast as possible. Corrected.
  • The genset stopped deloading and opened the breaker if it was 0.5 Hz over nominal settings. Corrected.

2.50.0

12/08/2010

New features:

  • VDO 3 can be used as temperature AND a Fuel sensor.

Changes:

  • Prompt for password when leaving block mode. Password level set in parameter 4901.
  • Ramp function implemented in Peak Shave mode.
  • Stop conditions in peak shaving improved.
  • VDO 2 calculations for level switch corrected.
  • MTU ADEC CAN communication improved.

2.40.2

17/10/2008

Improvement:

  • Stop command for Volvo and Scania engine communication changed

2.40.1

15/08/2008
  • Translations function corrected and max. number of languages reduced from 11 to 9

2.40.0

29/07/2008

New features:

  • Support of communication whit MTU-ADEC

Changes:

  • Volvo Penta EMS2 and SCANIA speed control updated.

2.31.3

12/12/2007
  • H2 option protocol now supports Modbus function 05 and 06.

2.31.2

29/10/2007
  • Password max limit changed to 32000.
  • Volvo Penta EMS2 preheat function updated.
  • Fire pump cooldown timer function updated.
  • M15 Analoge input measurements improved.

2.31.1

04/09/2007
  • Improved ramp up handling.
  • Volvo Penta EMS2 comm. error alarm updated.

2.31.0

19/06/2007

New features:

  • Regulation of reactive power, trough H2/H3

Changes:

  • Improved Ramp up delay handling.
  • Horn relay updated.
  • Improvement of external comm. enable input

2.30.3

16/01/2007

Changes:

  • Improved vector jump calculation.
  • BGC-L Input list updated

2.30.2

23/10/2006

Changes:

  • Handling of nominal power below 100kW updated.

2.30.1

28/09/2006

Changes:

  • GB handling updated.
  • IO view in util. SW updated.

2.30.0

05/09/2006

New features:

  • BGC-L for selected markets added.

Changes:

  • Frequency measurements >70Hz updated

2.21.2

26/06/2006

Changes:

  • GB operations adjusted upon back-sync-error.
  • Handling of MB close-failure updated.

2.21.1

08/03/2006

Changes:

  • Selection of Scania EMS 2 from USW updated.

2.21.0

24/02/2006

New features:

  • Scania EMS2 support added.

Changes:

  • Limit relay function updated.
  • Maximum frequency readout handling updated.
  • Volvo Penta EMS2 frequency change updated.
  • Power up sequence updated.

2.20.0

13/01/2006

New features:

  • Parallel enable added for Mains protections.
  • Channel 4800 (GOV / AVR relay setting) removed. Old relay settings was: GOV up: Relay 6, GOV down:
  • Relay 7, AVR up: Relay 8, AVR down: Relay 9.
  • Channel 4801-4804 added for GOV / AVR relay setting.
  • Auto start/stop input enabled in AMF.
  • Virtual input: Semi start, Semi MB off, Black busbar enable updated.
  • MLogic updated and new settings added.
  • Various Mlogic input / output added.
  • H5 Volvo Penta EMS 2 added.
  • Test mode setting: Simple, Full and Parallel.
  • Engine control relays configurable from MLogic when using Volvo Penta EMS 2
  • Self acknowledge added in USW. Channel 4452 "Auto reset warning FC" is removed.
  • Compact breaker handling added.
  • Manual control of GOV / AVR added for SEMI, TEST and AUTO.
  • DI alarms 1960-1990 added.
  • Actual language present in USW parameterlist.
  • Earth fault alarm and handling added.
  • Command timers output added to MLogic.
  • Selectable number of languages supported.
  • Service and master password settings available in JUMP menu.

Changes:

  • Overload 1 timer updated.
  • Horn function updated.
  • Gen-bar LED handling updated.
  • Short time parallel updated.
  • Semi mode handling updated.
  • Functionality of channel 2050 updated.
  • AVR reg. failure handling updated.
  • Mains fail handling updated.
  • MDEC protocol updated.
  • Scania protocol updated.
  • Back sync OFF functionality updated.
  • MB alarm updated.
  • Running detection updated.

2.12.2

28/11/2005

Changes:

  • MLogic command outputs updated.

2.12.1

17/11/2005

Changes:

  • Short time parallel updated
  • MLogic "MB synchronizing" updated
  • Minor updates

2.12.0

21/10/2005

New features:

  • Short time parallel added
  • VDE0108 sync. type updated

Changes:

  • Running, MB, GB offset updated
  • Password handling updated
  • Fuel pump logic/alarms updated
  • Short circuit precision updated
  • Hysterisys added to running detection
  • "Reset analogue input" functionality updated
  • M15 scaling added
  • FC updated on DI

2.11.1

30/06/2005

Changes:

  • Extended stop executed if running detection is lost

2.11.0

22/06/2005

New features:

  • MB trip failclass can be set in mains/bus protections
  • EIC alarms can be set to RUN activation

Changes:

  • GB trip stop failclass handling updated
  • Handling of overlap updated
  • Handling of view 3 updated

2.10.0

New features:

  • Support for MKIII PCB
  • Firepump cool down timer added
  • Delta V operation mode added

Changes:

  • Idle mode updated

On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).

Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.

DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.

DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.

Licence agreement for software downloaded from www.deif.com

Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.

The latest versions for full functionality

As always, we recommend that you install our offered improvements to fully utilise your DEIF product.

All improved software can be downloaded at your convenience at www.deif.com under “Software”.

Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.